Are you a service company, or do you also supply dental equipment?

We are a dental equipment service company first — repairs, call-outs, planned servicing and maintenance — and we supply equipment as well. Because the same engineers install, commission and then look after what we sell, one company is responsible if something needs putting right, rather than the supplier and the installer pointing at each other.

Can you repair dental equipment you did not supply?

Yes. We repair and maintain equipment installed by other companies, including Dürr Dental, Cattani, Ritter, Planmeca, Vatech, Carestream and Dentsply Sirona equipment.

Do you provide emergency call-out?

Yes. Breakdowns that stop a surgery are prioritised and, on weekdays, we aim to attend the same day. Call us and we will triage the fault on the phone first — sometimes there is a safe workaround until an engineer arrives.

Which areas do you cover?

We are based in the Midlands (Coventry and Birmingham) and work across the whole UK for equipment, installation and service projects. We are on site fastest in the Midlands; for the rest of the country we plan visits and installations in advance — ask us and we will confirm the date.

How do I get a price for a product?

Add the item to your quote list (or send us the model by phone or email) and we will come back with a price for the equipment, delivery and installation. Dental equipment pricing depends on configuration and site conditions, which is why we quote individually.

Does it need a separate amalgam separator?

No — amalgam separation is built into the VSA 300 S, with a removable collector that is replaced when the fill-level sensor signals it (typically every 6–9 months). UK practices must retain at least 95% of amalgam particles; the collector is part of how you demonstrate that.

What maintenance does it need?

Flush both suction hoses with cold water after each treatment, disinfect with a Dürr-approved agent at the end of the day, replace the amalgam collector when indicated, check the waste water valve annually and replace the exhaust bacterial filter once a year.

Can the spittoon drain into it?

Only through the special valve fitted between the spittoon drain and the VSA inlet, which ensures amalgam from the spittoon is also separated. We can supply and fit this as part of installation.

Dürr Dental VSA 300 S — Dürr Dental — Dürr Dental VSA 300 SDürr Dental

UK delivery

Installed by us

12-month warranty

Dürr Dental Dental suction units

Dürr Dental VSA 300 S

Combined wet suction unit for one surgery — vacuum, two-stage air/water separation and amalgam collection in a single unit.

Wet suction unit with integrated two-stage separation and amalgam collection
Designed for a single surgery — continuous S1 duty, 100% running time
Automatic amalgam level monitoring: warning at 95%, shutdown at 100%
Free air flow 670 l/min and vacuum −170 to −195 hPa
Supplied with the standard fitting kit, ready to connect

£2,278ex VAT

£2,733.60 inc VAT (20%)

Equipment price. Delivery, installation and commissioning are quoted separately.

Available to order

Call

Prices are quoted per practice. Delivery, installation and commissioning are priced with the equipment — ask us for a full quote.

Found the same model cheaper from an authorised UK dealer? We will beat it.

About this equipment

The VSA 300 S is Dürr Dental's combined wet suction unit for a single surgery. One unit generates the vacuum, separates air from waste water in two stages and collects amalgam sludge in a removable collector vessel — so it does the job normally split between a suction machine and a separate amalgam separator.

Separation works in two stages. The suction mixture enters a cyclone where centrifugal force throws water and solids against the outer wall; the air then passes a driven rotor which forms the second stage and keeps liquid and foam away from the turbine. Waste water runs through a centrifuge that removes amalgam particles before the flow leaves for the drain. The collector sits below the centrifuge, a sensor monitors the fill level and the unit refuses to run once it reaches 100% — so it cannot silently overflow.

Suction and exhaust air leave through 30 mm DürrConnect Special hoses and waste water through a 20 mm hose. The unit is permanently wired on 230 V with a 16 A type B breaker and an isolator, runs continuously (S1 duty) through a full clinical day, and can be installed at the same level as the surgery, inside a silenced housing, or on the floor below.

Typical use

Single-surgery practices with general or surgical lists
Practices without a separate amalgam separator in the unit
Replacing an ageing wet suction machine
Surgery upgrades where space in the room is tight

Technical data

Dürr Dental VSA 300 S — technical specifications
Manufacturer / type	Dürr Dental VSA 300 S (type 7125)
Intended for	1 surgery
Supply	230 V AC, 1~, 50 Hz
Power / current	580 W / 2.9 A (start-up current approx. 9 A)
Motor speed	2750 rpm
Free air flow	670 l/min
Vacuum at V = 0	−170 to −195 hPa
Max. liquid flow	5 l/min
Amalgam collector capacity	approx. 150 cm³
Collector replacement	Every 6–9 months, depending on workload
Dimensions (H × W × D)	48 × 31 × 31 cm
Weight	approx. 14 kg
Noise level	63 dB(A) without housing, 54 dB(A) with housing
Duty cycle	S1 (100%)
Protection class / IP	Class I / IP 21
Connections	Suction and exhaust air 30 mm, waste water 20 mm (DürrConnect)
Electrical protection	16 A type B MCB, multi-pole isolator
Order reference	7125-01/002 (230 V, 50 Hz)
Warranty	12 months as standard, extendable by 2 years

Specifications follow the manufacturer's published data. Confirm against the current data sheet before ordering — models are updated.

Installation & service

Supplied with the standard fitting kit, so it can be connected without ordering extras.
We install and commission the unit: fixed wiring, suction and waste connections, and a test of vacuum at the furthest point.
If the surgery has no spittoon or no rinse function, the variant with an integrated rinsing unit is required — we specify this at survey.
The amalgam collector is replaced as a service item and recorded for your maintenance file.
A bacterial filter on the exhaust air line is recommended and replaced annually.
A noise-reducing hood is available where the unit sits in or next to the surgery.
VSA or VS? The VSA 300 S includes amalgam separation; the VS 300 S is a different configuration. Compare the exact model, what is included and the installation scope — not just the model number.
Warranty: 12 months as standard, with a 2-year extension available. Tell us when ordering if you want the extension included.
Price excludes VAT. Delivery, installation and commissioning are quoted separately for your practice.

Questions about this model

At the same level as the surgery inside a ventilated cabinet or silenced housing, or on the floor below. It must not be installed in wet rooms and needs ambient conditions of +10 to +40 °C with humidity up to 70%. We survey the location before quoting installation.

Request a quote